Spec-first · Factory-neutralCertificates checked at source

Product Guides

Cryovials: Verify Vapor-Phase Storage vs. Liquid Immersion

A -196°C cryovial rating is not permission to immerse. Compare IFU phase wording, thread and gasket limits, IVD vs. RUO labels, and GUDID gaps before SKU approval.

· · 12 min read

Unbranded translucent polypropylene cryovials arranged on a warm off-white surface comparing an internal-thread cap with a silicone gasket, an external-thread cap, a capped self-standing vial, a stainless steel comparison rail, and an abstracted instruction sheet

A distributor quotes a 2 mL internally threaded polypropylene cryovial with a -196°C temperature line on its catalog sheet, and the hospital receiving team knows the lab stores specimens inside a liquid-nitrogen dewar. Before adding that SKU to the item master, the buyer needs to resolve a straightforward specification question: does a -196°C rating authorize liquid-nitrogen immersion, and what documentary evidence must the supplier provide first?

The answer: a -196°C rating is not permission to immerse

No. A buyer cannot treat a -196°C temperature rating as permission to immerse a cryovial in liquid nitrogen. Temperature resistance and permitted storage phase are two separate labeled-use claims. A polypropylene vial can withstand cryogenic temperatures down to -196°C and still carry an explicit manufacturer warning restricting use to the vapor phase above the liquefied gas.

In cryogenic storage, vapor-phase storage keeps vials suspended in the cold nitrogen gas zone above the liquid level, whereas liquid-phase immersion submerges the container directly into liquid nitrogen. That physical boundary matters because liquid nitrogen has low surface tension and can enter a screw-capped vial even when the cap is closed tightly. According to Purdue University Environmental Health and Safety guidance on liquid nitrogen, liquid nitrogen expands approximately 700 times in volume when it vaporizes and can embrittle and fracture materials, potentially leading to the explosion of a sealed container. Thermo Fisher Scientific's Nunc cryogenic tube FAQ similarly warns that liquid nitrogen can flow into cryostorage vials even when tightly capped and can trigger rapid expansion or vial failure upon thawing.

Read the phase sentence before the temperature number

A distributor listing can repeat a headline temperature figure from a catalog summary without the qualifying safety sentence that sits beneath it on the manufacturer's page or IFU. Across the three manufacturers checked for this review, explicit vapor-phase restrictions appear alongside cryogenic temperature ratings.

Manufacturer sourceStated temperature capabilityExact phase wording or warningProcurement takeaway
Thermo Fisher Nalgene 5005-0015 IFU (Rev B01, June 2024)Stores samples down to vapor-phase liquid nitrogen temperatures"For use in vapor phase of liquid nitrogen only. Submersion can lead to hazardous situation."Do not approve for liquid immersion; end user defines cold-storage conditions for the sample
Corning 431420 (2 mL internal-thread product page)Withstands temperatures to -196°C"Do not use cryogenic vials ... in the liquid phase of liquid nitrogen. Only store in the vapor phase above the liquified gas."-196°C rating coexists with an explicit prohibition on liquid-phase use
Greiner Bio-One Cryo.s (US category page)Suitable for -20°C, -80°C, and vapor-phase nitrogenTubes "must not be stored in the liquid phase of liquid nitrogen, but only in the gas phase above."Look for "gas phase" as a synonym for vapor-phase-only storage; confirm SKU IFU

Notice how three distinct phrases—"vapor phase only," "vapor phase above the liquified gas," and "gas phase above"—all establish the same procurement boundary. When reviewing a supplier quote, read for those phase phrases and for any mandatory secondary-barrier clause before relying on the temperature line. A catalog page can also lag behind or omit the full text of the controlled IFU, so the current IFU revision remains the controlling document for the exact SKU.

The four fields that belong in the procurement record

To prevent a buyer or receiving team from inferring immersion approval out of a single catalog number, map every candidate cryovial SKU across four separate specification fields: labeled temperature, permitted storage phase, closure and secondary-barrier requirement, and IVD or research-use status. Just as important, keep unconfirmed cells explicitly blank rather than filling them from adjacent SKUs or assumptions.

Example SKU or recordLabeled temperaturePermitted nitrogen phaseClosure and barrier detailIVD or RUO status
Thermo Fisher Nalgene 5005-0015 (15 mL, IFU Rev B01)Down to vapor-phase LN2 temperatures (end user defines sample storage)Vapor phase only; submersion hazard warningExternally threaded screw cap; no immersion barrier exception statedIVDR (EU) 2017/746 specimen receptacle (GMDN 47775)
Corning 431420 (2 mL product page)Withstands to -196°CVapor phase only; do not use in liquid phaseInternal-thread red cap with silicone washerDiagnostics application noted on page; verify exact market label
Corning GUDID records (H1084314201 / H1084314251)Blank (Storage and Handling: "No storage/handling found")Blank (not carried in GUDID record)Internal vs. external thread in device description only; gasket not detailedGMDN 47775 IVD specimen container; FDA code FMH; sterile, single-use
Thermo Fisher Nunc 363401 (product-family FAQ)Blank on checked FAQ excerpt (verify SKU IFU)Designed for vapor-phase freezing; liquid immersion only with secondary barrierInternal thread with silicone gasket; conditional heat-sealed CryoFlex sleeve required for immersionBlank on checked FAQ excerpt (verify SKU label)
Greiner Cryo.s (US shop category page)-20°C, -80°C, and vapor-phase nitrogenGas phase only; must not store in liquid phaseBlank at category level (check individual SKU sheet)CE marked (CE/IVD); verify market-specific labeling
Unverified distributor quote ("2 mL internal-thread, -196°C")-196°C (catalog claim only)Blank — hold liquid-immersion approval until IFU receivedInternal thread claimed; gasket and barrier requirements blankBlank — request IFU and unit label photo
flowchart TD
  A["Distributor quote lists -196C cryovial"] --> B["Obtain exact SKU current IFU and unit label"]
  B --> C{"Does IFU permit liquid immersion?"}
  C -->|"Vapor or gas phase only"| D["Restrict item master to vapor-phase LN2 or mechanical freezer"]
  C -->|"Phase omitted or blank"| E["Hold SKU unapproved for LN2 dewar"]
  C -->|"Liquid phase permitted with barrier"| F["Verify required secondary barrier and closure specs"]
  D --> G{"Verify intended diagnostic vs research label"}
  F --> G
  G -->|"IVD or CE IVD matches market"| H["Confirm UDI, sterility, and change-notice contact"]
  G -->|"Labeled Research Use Only"| I["Block clinical diagnostic use; route per facility policy"]
SKU qualification workflow: separate temperature claims, IFU storage phase, closure barriers, and IVD/RUO status before approval.

Internal vs. external thread: design intent, not an immersion rating

A tempting shortcut is to assume that internal-thread cryovials are safe for liquid nitrogen while external-thread vials are not. That shortcut confuses mechanical design intent with a regulatory or IFU immersion rating. In Thermo Fisher's Nunc cryogenic tube FAQ, the manufacturer explains that internally threaded tubes are designed for vapor-phase liquid nitrogen freezing, whereas externally threaded tubes are designed for mechanical freezing.

Even more telling is the conditional exception in that same FAQ. When asked about storing tubes immersed in liquid nitrogen, Thermo Fisher recommends an internally threaded design with a silicone gasket—a sentence that, read in isolation, can look like an endorsement of immersion. Immediately afterward, however, the FAQ warns that any mechanical closure carries a theoretical risk of liquid nitrogen entering the tube, states that immersion requires sealing the vial inside a heat-sealed CryoFlex secondary barrier, and explicitly warns users not to place the tubes in the liquid phase without that barrier.

Notice also how Corning's 431420 product page handles an internally threaded vial with a silicone washer: it still prohibits liquid-phase storage and directs users to store only in the vapor phase above the liquefied gas. None of the manufacturer documents checked here ranks one thread style as universally safe for immersion. From a supplier-quality standpoint, thread orientation is a design attribute to log alongside the cap seal—never a standalone substitute for the phase sentence in the SKU's IFU.

What a mechanical closure can and cannot promise

A threaded polypropylene cap with a gasket, O-ring, or washer—such as the silicone washer specified on Corning 431420, or the O-ring and integrated-gasket closures described in Thermo Fisher's sample storage tube features summary—improves mechanical seal consistency across routine handling, but it is not a hermetic seal. Thermo Fisher's FAQ notes that any sealing material becomes inflexible at ultra-low temperatures and that a theoretical risk of leakage exists whenever a mechanical closure is used; combined with liquid nitrogen's low surface tension, that is why the manufacturer requires a hermetically sealed protective envelope before liquid-phase storage.

For procurement and incoming quality teams, the goal is not to invent capping torque targets or laboratory freezing instructions—which the Thermo Fisher IFU leaves to the end user's validated procedures—but to document the exact closure system supplied under the SKU. Specifically, record whether the vial uses an internal or external thread, whether an elastomer gasket, O-ring, or washer is part of the cap assembly, and whether the manufacturer requires a secondary heat-sealed barrier sleeve before any liquid-phase contact. If a supplier changes cap resin, gasket compound, or secondary-barrier compatibility, that change alters the qualified specification.

IVD-labeled, CE IVD, or research-use only

A vial's cryogenic rating and sterility claim do not establish whether it is labeled for clinical diagnostic use. In hospital and diagnostic laboratory purchasing, IVD status and research-use-only (RUO) status are separate regulatory questions governed by the market in which the product is sold.

In the United States, a sterile specimen cryovial can fall under 21 CFR 864.3250 (specimen transport and storage container) and FDA product code FMH (Container, Specimen, Sterile). Under 21 CFR 864.3250, the device is Class I and 510(k) exempt; if it is not labeled sterile, it is also exempt from most Good Manufacturing Practice requirements aside from records and complaint files. Neither the regulation nor the FMH classification page prescribes a liquid-nitrogen phase or cap-thread design. Under FDA's In Vitro Diagnostic Device Labeling Requirements, IVD products intended for collecting, preparing, and examining human specimens must carry required IVD statements including "For In Vitro Diagnostic Use," whereas a product in the laboratory research phase that is not represented as an IVD is exempt from those labeling requirements only when it is prominently labeled "For Research Use Only. Not for use in diagnostic procedures."

In the European Union, the governing framework is Regulation (EU) 2017/746 (EU IVDR), which replaced the repealed IVD Directive 98/79/EC. Under IVDR Article 2(2) and 2(3), specimen receptacles are deemed in vitro diagnostic medical devices, while Article 1(3)(a) excludes general laboratory-use or research-use-only products unless specifically intended by the manufacturer for IVD examination. Manufacturers present CE IVD-marked cryotubes—such as the Nalgene 5005-0015 specimen vial compliant with IVDR (EU) 2017/746 and Greiner's CE/IVD Cryo.s line—for diagnostic workflows separate from general labware tubes, though Greiner's educational blog on CE and IVD cryovial selection still cites the superseded Directive 98/79/EC rather than the current IVDR text. Keep markets strictly separated in procurement files: a CE IVD mark does not satisfy US IVD labeling, and a US FMH Class I listing does not establish EU IVDR conformity.

What GUDID tells you, and what it leaves out

Receiving and master-data teams may look up a device identifier (DI) in FDA's Global Unique Device Identification Database (GUDID) hoping to verify storage limits directly. Two public AccessGUDID records for Corning 2 mL cryogenic vials show both the utility and the hard boundary of that lookup:

That absence is a record-level finding for those specific public DIs (whose public versions carry a March 2022 date), not proof that cryovial labels lack storage rules or that other GUDID entries cannot include handling fields. It shows why GUDID cannot replace the IFU: UDI records are suited to confirming device identity, regulatory classification, sterility, and single-use flags, as covered in our broader guides to labeled storage and transport evidence and specimen tube specification matching. When GUDID shows no storage/handling entry, buyers must read the exact package insert or unit label.

When the question is really about transport packaging

Specimen transport compliance can be conflated with cryogenic dewar storage, especially when a vial's intended use mentions both preservation and transport. Under 49 CFR 173.199, shipping Category B infectious substances requires triple packaging: a leakproof primary receptacle, leakproof secondary packaging with absorbent material for liquids, and rigid outer packaging, with the package capable of passing a 1.2 m drop test. For air shipments, the primary receptacle or the secondary packaging must also withstand a pressure differential of at least 95 kPa without leakage, and refrigerants such as liquid nitrogen are subject to separate conditions in the same section.

Those are distinct operational questions. Qualifying a cryovial as a primary receptacle in a UN 3373 shipper—detailed in our Category B specimen packaging guide—does not approve that vial for liquid-nitrogen immersion inside a storage dewar. Conversely, a vapor-phase storage statement on an IFU does not show that the vial, or the secondary packaging it ships in, meets the 95 kPa air-transport requirement; that evidence comes from packaging qualification records.

A supplier evidence request for the exact SKU

Before releasing a cryovial SKU for hospital or clinical-lab purchase, send a short verification request tied to the exact catalog number and UDI-DI rather than a generic family brochure. Each item in the checklist below maps directly to the documentary gaps identified above.

Evidence itemWhat to request from the supplierWhy it blocks substitution errors
Exact IFU revision and effective dateCurrent controlled IFU PDF for the exact SKU, not a category flyerCatalog pages can omit phase warnings or lag behind revision updates
Verbatim storage-phase sentenceExact text stating vapor/gas phase only, mechanical freezer, or permitted liquid-phase useSeparates -196°C material claims from permitted liquid-nitrogen phase
Closure and secondary barrier specThread style (internal or external), gasket/washer presence, and any mandatory secondary sleevePrevents unapproved immersion without a required heat-sealed barrier
Legible unit and pack label photoPhoto showing temperature-limit symbols, sterile/single-use marks, and UDI carrierConfirms label symbols (e.g., ISO 15223-1) match the IFU and receiving barcode
IVD, CE IVD, or RUO declarationMarket-specific regulatory statement, FDA FMH/21 CFR 864.3250 or EU IVDR 2017/746 evidenceKeeps RUO labware out of clinical diagnostic workflows
Sterility, shelf life, and change contactSterilization standard (where claimed), labeled shelf life, and pre-change notification contactTriggers re-review before a cap, resin, or sterilization change ships

Anchor that change-notification requirement in your supplier agreement so cap design, gasket material, or labeling revisions cannot roll through silently; see our guide to quality agreements for consumable suppliers for practical change-control clauses.

Limits and recheck triggers

This review checked primary technical documents from three manufacturers (Thermo Fisher Scientific, Corning Incorporated, and Greiner Bio-One) alongside US and EU regulatory texts and two AccessGUDID records, all checked on November 15, 2026. It is not a market-wide census of all cryovial brands, and no laboratory immersion, rupture, or shelf-life testing was performed. Because ISO 15223-1:2021 is paywalled beyond its public abstract, symbol usage here relies on the public abstract and the ISO 15223-1 symbols glossary printed in the Thermo Fisher Nalgene IFU. Manufacturer IFUs, catalog pages, and GUDID entries are revision-, catalog-, and market-specific and can change without notice.

Re-verify the SKU file whenever any of the following triggers occur:

  • A new IFU revision or unit-label update for the approved SKU, especially any change between vapor-phase-only wording and liquid-phase permission.

  • Any change to cap thread geometry, silicone gasket or washer design, secondary-barrier compatibility, manufacturing site, or sterilization process.

  • A new GUDID device identifier, labeler update, or newly populated Storage and Handling field.

  • An FDA, EU IVDR, or ISO 15223-1 symbol change, a recall or field-action notice involving vial leakage or rupture, or a facility change from vapor-phase storage to liquid-nitrogen immersion.

Sources